Comnet CNGE2FE8MSPOE Información técnica Pagina 64
- Pagina / 162
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
57
6.11 IP Security
IP security function allows the user to assign 10 specific IP addresses that have permission
to manage the switch through the http and telnet services for the securing switch
management. The purpose of giving the limited IP addresses permission is to allow only the
authorized personnel/device can do the management task on the switch.
IP Security Mode: Having set this selection item in the Enable mode, the Enable
HTTP Server, Enable Telnet Server checkboxes and the ten security IP column fields
will then be available. If not, those items will appear in grey.
Enable HTTP Server: Having ticked this checkbox, the devices whose IP addresses
match any one of the ten IP addresses in the Security IP1 ~ IP10 table will be given the
permission to access this switch via HTTP service.
Enable Telnet Server: Having ticked this checkbox, the devices whose IP addresses
match any one of the ten IP addresses in the Security IP1 ~ IP10 table will be given the
permission to access this switch via telnet service.
Security IP 1 ~ 10: The system allows the user to assign up to 10 specific IP
addresses for access security. Only these 10 IP addresses can access and manage
the switch through the HTTP/Telnet service once IP Security Mode is enabled.
And then, click to have the configuration take effect.
[NOTE]
Remember to execute the “Save Configuration” action, otherwise the new
configuration will lose when the switch powers off.
- CNGE2FE8MSPOE 1
- FCC Warning 2
- CE Mark Warning 2
- Content 3
- Chapter 1 Introduction 8
- 1.2 Software Features 12
- 1.3 Package Contents 15
- 2.1 Physical Dimension 16
- 2.2 Front Panel 16
- 2.3 Top View 17
- 2.4 LED Indicators 18
- 3.1 Installation Steps 20
- 3.2 DIN-Rail Mounting 21
- 3.4 Wiring the Power Inputs 25
- 3.6 Cabling 27
- Transceiver Inserted 28
- Remove LC connector 30
- 4.1 X-Ring Application 33
- 4.3 Dual Homing Application 35
- Chapter 5 Console Management 36
- Console login interface 38
- 5.4 CLI Management 39
- 5.5 Commands Level 39
- 6.3 System Login 42
- 6.4 System Information 43
- 6.5 IP Configuration 44
- IP configuration interface 45
- 6.6 DHCP Server 46
- 6.6.1 System configuration 47
- 6.6.2 Client Entries 48
- 6.6.3 Port and IP Bindings 49
- 6.7 TFTP 50
- 6.7.2 Restore Configuration 51
- 6.7.3 Backup Configuration 52
- 6.8 System Event Log 53
- SMTP Configuration interface 56
- 6.9 Fault Relay Alarm 59
- 6.10 SNTP Configuration 60
- SNTP Configuration interface 63
- 6.11 IP Security 64
- IP Security interface 65
- 6.12 User Authentication 66
- 6.13 Port Statistics 67
- Port Statistics interface 68
- 6.14 Port Control 69
- Port Control interface 70
- 6.15 Port Trunk 71
- LACP disabled 73
- LACP enabled 75
- 6.15.3 State Activity 79
- State Activity of Switch 2 80
- 6.16 Port Mirroring 81
- 6.17 Rate Limiting 82
- 6.18 VLAN configuration 84
- 6.18.1 Port-based VLAN 85
- 6.18.2 802.1Q VLAN 88
- 802.1Q Configuration 89
- Group Configuration 91
- 6.19 Rapid Spanning Tree 93
- 6.19.2 Port Configuration 95
- 6.20 SNMP Configuration 97
- 6.20.2 Trap Configuration 99
- 6.20.3 SNMPV3 Configuration 100
- 6.21 QoS Configuration 103
- QoS Configuration interface 104
- 6.21.2 Port-based Priority 105
- 6.21.3 COS Configuration 105
- 6.21.4 TOS Configuration 105
- 6.22 IGMP Configuration 107
- IGMP Configuration interface 108
- 6.23 X-Ring 109
- X-ring Interface 110
- 6.24 LLDP Configuration 111
- 6.25.1 System Configuration 112
- 6.25.2 Port Configuration 114
- 6.25.3 Misc Configuration 116
- 6.26 MAC Address Table 117
- 6.26.2 MAC Filtering 119
- 6.26.3 All MAC Addresses 120
- 6.27 Power over Ethernet 123
- 6.28 Factory Default 125
- 6.29 Save Configuration 126
- 6.30 System Reboot 127
- Troubles shooting 128
- RJ45 Pin Assignments 129
- Cross over cable schematic 130
- Cross over cables schematic 132
- RJ45 Pin Assignment of PoE 133
- Appendix B—Command Sets 135
- Halt and perform a cold 136
- Port Commands Set 138
- Trunk Commands Set 141
- VLAN Commands Set 142
- Spanning Tree Commands Set 144
- QOS Commands Set 147
- IGMP Commands Set 147
- LLDP Commands Set 149
- SNMP Commands Set 150
- Port Mirroring Commands Set 152
- 802.1x Commands Set 153
- TFTP Commands Set 155
- SNTP Commands Set 159
- X-ring Commands Set 160
- PoE Commands Set 161
- Communication Networks 162
Relacionado con productos y manuales para Redes Comnet CNGE2FE8MSPOE
Redes Comnet CNGE3FE7MS4 Información técnica
(104 paginas)
(104 paginas)
Redes Comnet CNGE2FE8MSPOE Información técnica
(107 paginas)
(107 paginas)
Redes Comnet CWGE2FE24MODMS Información técnica
(84 paginas)
(84 paginas)
Redes Comnet CNGE24MS Especificaciones
(108 paginas)
(108 paginas)
Redes Comnet CWFE8MS/DIN Manual de usuario
(20 paginas)
(20 paginas)
Redes Comnet CWFE8MS/DIN Información técnica
(75 paginas)
(75 paginas)
Redes Comnet CWGE28FX4TX24MS Especificaciones
(117 paginas)
(117 paginas)
Redes Comnet CWGE2FE8MSPOE Información técnica
(143 paginas)
(143 paginas)
Redes Comnet CNGE2FE8MSPOE Manual de usuario
(7 paginas)
(7 paginas)
Redes Comnet CNGE28FX4TX24MSPOE+ Especificaciones
(112 paginas)
(112 paginas)
Redes Comnet CNGE2FE8MSPOE Manual de usuario
(32 paginas)
(32 paginas)
Redes Comnet CNGE24MS Manual de usuario
(82 paginas)
(82 paginas)
Unicol VSX1800 manuels
Manuels d'utilisation et guides de l'utilisateur pour Supports de sol en panneaux plats Unicol VSX1800.
Nous fournissons des manuels en pdf 1 Unicol VSX1800 à télécharger gratuitement par type de document : Manuel d'instructions
Comentarios a estos manuales